The Honest Answer Up Front
A drafty door is almost never a mystery and almost never needs a new door. Cold air gets in through four specific paths: the gap under the slab, the weatherstrip running up the latch side and across the top, the joint where the threshold meets the door bottom, and, in the doors nobody wants to hear about, the door itself having drifted out of square so none of the seals touch anything anymore. Each path has a known fix, the fixes together cost a fraction of replacement, and an afternoon with a screwdriver, a tape measure and the right parts returns most doors to draft-free condition.
The honest sequence we work through on our window and door service calls is diagnose, seal, align, and only then consider the door. Skipping straight to a replacement quote is the most common way homeowners spend four figures solving a fifteen-dollar weatherstrip problem, and it happens constantly because a new door is easy to sell and a Saturday of sealing is not. When replacement genuinely is the answer, an installed entry door runs $2,400 to $4,800 in Metro Vancouver, and that price deserves to be reached honestly.
One expectation to set before the screwdrivers come out: sealing is about comfort first and bills second. A leaky door makes the hallway cold, the thermostat confused and the couch untenable, which is worth fixing on its own. On the utility bill, a single door draft is a modest line item, and anyone promising dramatic bill rescue from one tube of caulk is selling something. Do the work for the warm hallway, then aim bigger envelope money at the upgrades that actually pay, the subject we rank properly in Chapter 9 and in our energy upgrades guide.
Seal the four paths in order, align the door, and only then let anyone quote you a new one. Most doors never earn the quote.
0 jobs since 2010
Door, window, plumbing, heating and cooling calls across Metro Vancouver, including hundreds of drafts that ended with weatherstrip, not replacement.
0 on every door
Sweep gap, jamb weatherstrip, threshold joint and alignment drift. Diagnose in this order and the fix is usually obvious.
0 star rated
26 verified Google reviews, with door assessments where the honest answer was a sweep and a hinge screw.
0 workmanship warranty
On every door we seal or install, in writing, on top of manufacturer coverage on hardware and slabs.
Find the Leak in Ten Minutes
Diagnosis comes before parts, and the tools are already in your kitchen. The incense test is the gold standard: on a breezy day, light a stick of incense, hold it an inch from the door perimeter and move it slowly along the threshold, up the latch side, across the header and down the hinge side. Where the smoke bends toward the door or streams into the room, you have found moving air. Mark each spot with painter's tape, because three days from now you will not remember which corner it was.
Two supporting tests round out the picture. The daylight test at night, interior lights off and porch light on, reveals gaps the smoke test misses, especially at corners where weatherstrip meets weatherstrip. And the paper test checks compression rather than leakage: close the door on a strip of paper at several points around the perimeter and tug. Paper that slides out easily means the weatherstrip at that spot is worn, crushed or no longer touching, which is a pressure problem rather than a hole. A door that passes the paper test everywhere but still drafts is leaking at the threshold or the frame, not the jamb seals.
Pick a windy day
Moving air is the whole point of the test. A still afternoon finds nothing, and everything changes when the outflow blows.
Run the incense stick
Slow passes an inch from every seal edge, threshold to header, hinge side to latch side. Mark each bend in the smoke with tape.
Check for daylight
Lights off at night, exterior light on: any visible sliver of light is a visible gap. Corners are the usual offenders.
Test weatherstrip compression
Close the door on paper strips at intervals. Paper that slides out freely marks worn or misadjusted weatherstrip.
Write the map
A photo of the taped door with notes is a parts list, a DIY plan and a pro briefing in one.

The Four Leak Paths on Every Door
Doors leak where their geometry forces gaps. A slab swinging in a frame needs clearance to operate, so every functional door carries engineered gaps at the perimeter, and sealing is the art of closing those gaps when the door is shut without preventing it from moving when it is not. The four paths below account for essentially all residential door drafts, in rough order of frequency.
| Leak path | What you notice | The fix |
|---|---|---|
| Under-door gap at the sweep | Cold feet, curtain movement, dust line on the floor near the door | Replace or adjust the door sweep; the most common single draft source |
| Latch-side jamb weatherstrip | Smoke test bends along the strike jamb, paper slides out at mid-height | Replace worn compression strip or V-strip; adjust strike plate to press it tighter |
| Threshold joint | Draft at ankle height across the threshold width, often worse in wind-driven rain | Adjust the threshold, fit a new threshold gasket, pair with a sweep that meets it |
| Frame, corners and slab alignment | Daylight at the corners, door self-opening or rattling, weatherstrip touching on one side only | Realign the door with hinge work and shims, or address frame movement and rot |
Two honourable mentions belong on any complete list. Mail slots leak air straight through the slab, fixed with a quality brush-backed flap or a full cover plate. And glass sidelites beside the door are windows in their own right, with their own seals and, in older homes, single panes that radiate cold in a way the door slab never will. A draft blamed on the door for years is sometimes a sidelite doing the leaking, which the incense test reveals in the first minute.
Diagnose in the order the air actually moves: sweep, weatherstrip, threshold, alignment. Fix them in the same order and each fix gets a fair test.
Weatherstripping Compared, Honestly
Weatherstripping is where the coastal climate earns its reputation for destroying hardware-store optimism. The Lower Mainland hands exterior seals three things in rotation: months of rain that swells and softens absorbent materials, an annual cold snap that freezes stiff anything porous, and enough UV in summer to embrittle the cheap stuff. The comparison below is filtered through all three.
| Type | How it seals | BC rain verdict | Best use |
|---|---|---|---|
| Compression bulb (silicone, EPDM) | A hollow bulb crushed against the door face | Excellent: tolerant of wet, freeze and UV cycles | Jamb and header seals on any exterior door |
| Spring bronze V-strip | Springy metal legs flex against the moving door | Excellent: decades of service, unaffected by wet | Older wood doors, heritage homes, painted frames |
| Magnetic strip | Magnets in the frame pull a steel rail on the door | Excellent seal, best on flat, true doors | Fibreglass and steel door pairs built for it |
| Brush pile with fin | Fine brush plus a plastic fin wiping the gap | Good, with a quality fin; bare brush leaks air | Sliding patio doors and some sweep designs |
| Adhesive foam tape | Squashy foam stuck in the gap | Poor: absorbs water, freezes, peels within a wet season or two | Temporary patch, interior doors, never exterior |
| Felt | Dense felt pressing the gap | Poor outdoors: saturates, wicks water, freezes solid | Interior only, or the inside face of a storm door |
Two practical notes from the field. First, buy weatherstripping by the door's actual gap and geometry, not by the photo on the package: measure the reveal, note whether the door closes against the strip's face or compresses it into a channel, and match the system the door was designed for. A mismatched seal either does nothing or fights the latch so hard the door will not close. Second, replace all the perimeter seals on a door as a set, top and both sides. Mixing a fresh dense bulb with two crushed decades-old corners just moves the draft to the weakest remaining seal.
The Door as a Sealed System, Not a Bag of Parts
The shift that separates a sealed door from a decorated one is thinking in systems. A door seals at the moment of closing, in a specific order, with parts that are engineered to meet each other: the sweep rides down onto the threshold's rising ramp, the latch-side bulb compresses against the strike-side stop as the bolts throw, and the header strip comes down last over the top rail. Get the geometry right and the whole perimeter loads together, a gasketed assembly with an airtight latch. Get it wrong, in the classic homeowner sequence of new sweep over an old sagging threshold with one stripped hinge screw, and every part is fighting the others while the draft sails through the arbitration.
Wind-driven rain is the BC-specific stress test. A February southwesterly pushes water up an unshielded threshold in a way that plain air never tests, which is why threshold design in this region leans on a stepped or ramped profile with a dedicated gasket, not a flat bar and hope. The ramp gives runoff somewhere to be, the gasket gives wind a wall, and the sweep applies pressure to both. When a customer describes water appearing at the door base during storms but never during ordinary rain, the answer is almost never the roof or the slab, it is a threshold and sweep pairing that stopped working as a pair.
True the door first
Hinges tight, slab square, door resting evenly on its weatherstop before any seal touches it. Sealing a crooked door seals the crookedness in.
Set the threshold
Adjust or replace so the ramp sits level with the finished floor, fastened solid, gasket seated, screws not stripped.
Fit the sweep to the threshold
Sweep meets the threshold's ramp with even contact across the full width: the pair is the seal, not either part alone.
Hang the jamb and header strips
Continuous runs on latch side and top, corners joined neatly, compressing evenly when the latch throws.
Close, latch, and test the whole system
Paper test at intervals, incense on a windy day, and one final look for daylight at night. Fix what moves, in this order.
That sequence is why professional sealing visits can look unhurried. The parts installation is the fast bit; the truing and the pairing are the work, and they are what separates a door that stops the January wind from a door that has new parts on it.
Thresholds and Sweeps: The Ankle-Height Team
The threshold-sweep pair is the hardest-working seal on the door, because it guards the largest gap against the dirtiest conditions: water, grit, foot traffic and the highest wind pressure of any perimeter location. Thresholds divide into three useful families. Adjustable thresholds carry screws along their length that raise or lower a centre rail to meet the sweep, letting you tune the seal as the door and house settle. Fixed ramps rely on pairing with the right sweep height. And thermal-break thresholds add an insulating barrier inside the metal profile for the homes where every degree of floor cold matters.
| Sweep style | Sealing action | Honest notes |
|---|---|---|
| Bulb sweep with vinyl insert | A round profile compresses along the threshold ramp | The best all-round seal; replace the insert, not the whole bar, when it wears |
| Fin sweep with brush | A flexible fin wipes the threshold while brush damps drafts | Great on uneven thresholds and for rain; quality varies wildly, buy the good one |
| Brush-only sweep | Bristles drag the gap | Comfortable underfoot and quiet, but the leakiest option on a windy exposure |
| Automatic door-bottom | A mechanism drops the seal when the door closes, lifts it on opening | The tightest seal available, and worth it where wind or noise is serious |
| Under-door retrofits, stick-on types | Adhesive-backed fins applied to the door face | A stopgap for renters and lazy Saturdays, not a strategy |
Outflow cold is the local exam. A couple of times each winter, Arctic outflow funnels frigid, dry air through the Fraser Valley and turns every marginal seal in its path into a whistle. Those are the nights that generate our door-draft call spikes from the North Shore and the eastern valleys, and they are the reason our North Vancouver windows and doors crews specify bulb-and-gasket threshold pairs rather than brush sweeps for wind-exposed entries. If your door only bothers you on a handful of nights a year, it is telling you exactly which kind of night to seal for.
When the Door Itself Is the Problem
Sometimes the draft is the least of the door's issues, and the door is the draft. Alignment failure is the common form: hinges wear, the top hinge pulls its screws out of a tired jamb, and the slab sags a few millimetres, enough to open a gap at the top corner while crushing the weatherstrip at the bottom. The quick fixes are real fixes: drive three-inch screws through the top hinge into the framing behind the jamb, shim the hinge slightly to re-square the slab, and adjust the strike plate until the door compresses its seals evenly and latches without effort.
Coastal moisture writes the longer-term story. Solid wood slabs in older Vancouver and Burnaby homes cycle with the seasons, swelling in the wet months enough to bind, shrinking in the dry August interiors enough to show daylight, and over years they can twist permanently so no stop or seal ever meets them evenly again. Rot in the jamb or sill is the structural version, soft wood at the threshold corners that no weatherstrip can compensate for, and it is the point where sealing stops being the honest plan. Fibreglass and steel slabs, which hold their geometry for decades and ignore the rain, are what we install when that point arrives, a comparison our Surrey windows and doors team walks homeowners through on every door assessment.
The checklist that separates an alignment problem from a finished door is short. If the slab still closes square, the hinges can be tightened, the frame is solid when pushed, and there is no soft wood anywhere, the door is a candidate for sealing. If the slab twists, the frame moves, the corners are soft, or the door is a 1970s hollow-core unit doing exterior duty it was never designed for, replacement is the fix that stops pretending.
DIY Versus Calling a Pro
The honest division of labour favours the homeowner for most sealing work. Sweep replacement, jamb weatherstripping, threshold gaskets, mail-slot flaps and strike-plate adjustment are all screwdriver-and-tape-measure jobs, and doing them yourself is faster than booking anyone. The tools are basic, the parts are labelled with the door measurements, and the tests from Chapter 2 tell you immediately whether the fix landed. What DIY demands is the discipline from Chapter 5: true the door first, work the threshold-sweep pair as a system, and finish with the paper test rather than hope.

Bring in a pro when the diagnosis is structural or the stakes rise. Frame rot, slabs warped past honest adjustment, doors in security-critical positions, heritage units where the hardware itself is part of the house, and multi-door projects bundled with window work are all territory where a flat-rate visit is cheaper than the second and third rounds of hardware-store parts. And when the answer is replacement, the assessment becomes an estimate: an installed entry door runs $2,400 to $4,800 across Metro Vancouver, with slab material, glass sidelites and hardware driving where a specific door lands in the range.
The Honest Cost Math
Start with the uncomfortable truth: a single drafty door is a comfort problem more than a bill problem. Sealing one beautifully takes a modest pile of parts and an afternoon, and it transforms the hallway immediately, but the monthly heating arithmetic of one door's perimeter is small against a whole-house envelope. Anyone selling dramatic bill rescue from door weatherstripping is selling theatre. The compounding version of the story is real, though: a house with a drafty door usually has a drafty everything, and air-sealing as a campaign, doors, windows, attic hatches, outlets on exterior walls, is one of the highest-return moves in our energy upgrades guide.
| Strategy | Cost | What it buys |
|---|---|---|
| Full DIY seal: sweep, weatherstrip set, threshold gasket, adjustment | A modest hardware-store run | Warm hallway, quiet door, honest comfort, immediate feedback |
| Professional sealing visit, quoted flat-rate | A fraction of replacement | Truing, system pairing and the parts specified for the exposure, warrantied |
| Entry door replacement, installed | $2,400 to $4,800 | A modern insulated slab, new frame, real security hardware, and decades of sealing headroom |
| Door plus window package | Project-priced, windows from $650 to $950 per unit | The full-envelope version, worth a single coordinated quote when everything is tired at once |
When replacement is the honest verdict and the timing is wrong for the budget, the door program qualifies for financing from 7.99 percent with approved credit through our financing options, and door and window rebates may apply — we check eligibility and handle paperwork.
The Doors People Forget
The entry door gets all the complaints, and four quieter doors do a surprising share of the leaking. The back door to the deck or yard is usually an older, cheaper unit than the front, seals like it, and hides behind a blind. The garage man-door, connecting house to garage, matters twice over: it leaks, and it is also the door whose seals protect your air quality from everything evaporating in the garage, which makes it the one door whose weatherstrip genuinely should never be optional.
Basement doors to walk-outs and utility rooms swing through the largest indoor-outdoor temperature differences in the house and are often the oldest hardware on the property. And storm doors, the double-edged classic: a well-set storm door with intact sweeps and a functioning closer adds a real buffer air gap to the entry behind it, while one with a broken closer and a torn screen spends the winter banging wind through its gaps. The patio door deserves a sentence of its own, sliding doors leak by design through their brush seals and the interlock where the panels meet, and upgraded pile weatherstrip with a fin plus an adjusted anti-lift and a new panel sweep is one of the highest-comfort-per-dollar jobs in the whole house. The full enclosure version of that story, including when sliders deserve replacement, is covered in our Vancouver window replacement guide.
The BC Seasonal Calendar for Door Seals
Coastal doors live on a cycle, and maintenance scheduled against the cycle lasts three times longer than maintenance scheduled against memory. The calendar below is the one our crews work to, tuned to the Lower Mainland's rhythm of wet winters, dry interiors in August and the outflow snap that arrives without much warning in January.
| When | What to do | Why now |
|---|---|---|
| October, before the rains set in | Full perimeter test, paper and daylight, replace anything worn | Catch the seals while the weather still forgives an hour outside |
| November to February, monthly glance | Check the sweep and threshold after heavy wind-driven rain events | Storm season is the exam; a two-minute look catches failing gaskets early |
| After the first outflow cold snap | Night-light test on the windiest door, feel for whistles | The only real test of cold-air sealing is the cold air itself |
| March, as rains ease | Tighten hinge screws, re-true the slab, adjust the strike | A winter of swelling and drying leaves doors subtly out of square |
| August, the dry interior stretch | Re-check clearances and touch up finish at the sill corners | Wood is at its smallest now: gaps you see now are the real gaps |
| Any season, before booking a replacement | One last paper and incense pass on the whole system | Spend four figures only after fifteen dollars has genuinely failed |
The quiet month matters most. August's dry air shrinks wood slabs and jambs to their minimum, which makes it the honest season for measuring what is permanent versus what is merely February. A gap that closes in August and opens in January is seasonal movement, and the fix is flexible seals and a properly compressed system. A gap that is identical in both months is a geometry problem, and that is the door asking for hinge work or, if the frame is involved, the honest replacement conversation.
The One-Page Cheat Sheet
The whole guide compressed for the toolbox. Work top to bottom, in order, and stop the moment the paper test passes.
| Question | The answer |
|---|---|
| Where is my draft? | Incense on a windy day plus the night daylight test: sweep, jamb strip, threshold, alignment, in that order |
| Which weatherstrip for BC? | Compression bulb in silicone or EPDM, or spring bronze. Never felt or bare foam tape outdoors |
| Threshold and sweep? | A pair, not parts: ramped threshold, bulb or fin sweep meeting it evenly across the full width |
| Door out of square? | Three-inch screws in the top hinge, shim to re-true, adjust the strike plate, then seal |
| DIY or pro? | DIY the parts, pro the structure: rot, warp, security doors and bundled projects |
| When to replace? | Rot in the frame, slab twisted past honest adjustment, security needs, or a bundled envelope project |
| What does a new door cost? | $2,400 to $4,800 installed in Metro Vancouver, driven by slab, glass and hardware |
| Will it save the bill? | Comfort first; the bill payoff lives in whole-envelope air sealing, not one door's weatherstrip |
Frequently Asked Questions
Services From This Guide
Door sealing assessments and entry door replacement quotes across Metro Vancouver: find the leak, fix the leak, or replace the door when the honest answer is replacement.
Window and door services
Door sealing, alignment and replacement plus energy-efficient window installs, all with written flat-rate quotes.
Windows and doors in Vancouver
City crews for door drafts, alignments and replacements across Vancouver, from heritage homes to condos.
Windows and doors in Burnaby
Sealing assessments and door work across Burnaby and New Westminster, usually booked within days.
24/7 emergency service
Plumbing and heating emergencies answered around the clock, average 45-minute response, flat after-hours premium.
Related Guides
The Vancouver Window Replacement Guide
When the whole envelope needs work, the window guide covers measuring, packages and install day.
Rebates & MoneyEnergy Efficient Upgrades for BC Homes
Where door and window sealing sits in the ranked list of upgrades that actually move a BC Hydro bill.
MaintenanceWinter Prep for the Vancouver Home
The October checklist that catches drafts before the outflow cold arrives, doors included.
Red Seal certified, licensed gas fitters (BC-PL-2019-4421), $2M insured and 15-plus years in the field, with more than 12,000 jobs completed across Metro Vancouver since 2010 and a 5.0-star rating across 26 Google reviews. We wrote this guide because nine door drafts out of ten are fixable in an afternoon with the right fifteen-dollar part, and homeowners deserve to know that before anyone sells them a four-thousand-dollar door they do not need yet. To book instead of DIY, see window & door service in Vancouver — same-day across the city.
More about our team →Get Your Door Draft Diagnosed and Priced
Book a free door assessment with a Red Seal estimator. You get the leak located, the fix quoted flat-rate, an honest replacement read if the door is finished, and financing options from 7.99 percent with approved credit if replacement wins. Zero obligation, quotes on most calls within days. If you would rather hand this to a pro, our window & door services pages cover Metro Vancouver.
Cold air coming through the door?
Free door assessments across Metro Vancouver, usually booked within days, with the fix quoted flat-rate before we touch a thing. Plumbing or heating emergency in the meantime? The 24/7 line is answered around the clock with flat after-hours pricing posted in advance.
Call 604-615-2212 WhatsApp Us